Näytä kirjoitukset

Tässä osiossa voit tarkastella kaikkia tämän jäsenen viestejä. Huomaa, että näet viestit vain niiltä alueilta, joihin sinulla on pääsy.


Viestit - upamfva

Sivuja: 1 ... 46 47 [48] 49 50 ... 177
706
Mazda’s New PHEV Is Often All-Electric, But Greens Aren’t Happy



The search for perfection often blocks good outcomes, French philosopher Voltaire said. Some green opposition to plug-in hybrid electric vehicles (PHEV) reminds critics of the great man’s words.Get more news about Carburetor For Mazda,you can vist our website!

PHEVs provide an impressive transition between internal combustion engines (ICE) and battery electric vehicles. They can provide up to 50 miles of electric-only range, although the Mazda CX-60 PHEV I’ve just been driving managed just over an average 31 miles per gallon (37 miles per U.S. gallon). But green lobby groups protest their use because they allow a role for ICE technology.

Surveys of average car and SUV use show many motorists would find this was enough range, even with the Mazda. It would take care of much daily driving including local commuting, school runs and shopping. Long distances can be rarer but if required, a PHEV can easily just switch seamlessly to the combustion engine and handle the long summer trip to the sun or the skiing trip, for maybe 400 miles or more.
Green lobby groups claim battery electric vehicles (BEV) are capable of an all-round role. But my experience shows that so far, the technology is not up to it. So range anxiety, coupled with the current shortage or hopeless inefficiency of the European charging network makes the idea of a PHEV very seductive.

To be fair to green lobby groups like Brussels-based Transport and Environment (T&E), they do have a genuine gripe about PHEV abuse. For instance, some big fleet operators used fat government subsidies to replace their ICE vehicles with PHEVs, but because their driver's gas was paid for, there was no incentive to plug the vehicles in to electric chargers. Overall output of carbon dioxide (CO2) actually went up because these vehicles with 2 engines are heavier. So “Ban PHEVs”, says T&E.
The European Union (EU) has banned the sale of new ICE vehicles by 2035, including hybrids and PHEVs. The California Air Resources Board (CARB), whose rules may be accepted by some U.S. states, has also banned the sale of new ICE vehicles by 2035. But it has given PHEVs a limited dispensation because it felt poorer people in rural locations might find BEVs too expensive or impractical. Britain has banned the sale of new ICE vehicles by 2030, but so far hasn't decided the fate of hybrids.

707
Fluke New Explosion Proof Flashlight Series



Fluke, the largest supplier of intrinsically safe measurement tools, expands its line of EX products with the Fluke Intrinsically Safe Flashlights. In hazardous, potentially explosive work zones, safety is the main concern. The new flashlights are great for general purpose lighting, but also offer a design specific for safe use in hazardous work sites in oil and gas, petrochemical, pharmaceutical processing, mining, paint shops, and other potentially explosive areas.Get more news about Buy Explosion Proof Flashlight,you can vist our website!

Four models to fit your workload:

- Fluke FL-45EX – Convenient and compact. This pocket-sized light is great for lighting in small, crowded spaces or wherever you need it.

- Fluke FL-120EX – Comfortable enough for everyday use. This light fits in your tool belt and features an ergonomic design with an over molded rubber grip and a push-button for high and low light modes.

- Fluke FL-150EX – Light for any workspace. This light fits in your tool belt and offers a high, low and a strobe light mode to give you the light you need wherever and whenever you need it.

- Fluke HL-200EX – Hands-free headlamp. This headlamp securely grips your hardhat, leaving your hands-free for whatever your job demands. The light features an adjustable angle, as well as high and low light modes.

708
Best RFID-blocking wallets and bags in 2023



Tap-and-pay (RFID-capable) credit cards can lead to a potential security hazard: criminals swiping your credit card information while your cards are in your bag or wallet, simply by walking close to you. Find out how likely this scenario is and what you can do about it ahead.Get more news about Best Rfid Wallet,you can vist our website!

What does RFID mean?
RFID stands for radio frequency identification. This technology uses radio waves to identify objects. If you can tap and pay with your credit card, it is RFID-capable.

There are wallets and bags on the market that can block RFID scanning. While it's technically possible for a thief to steal your credit card information via RFID, this kind of hacking is not a widespread crime, according to the Identity Theft Resource Center. Still, an RFID-protected wallet or bag might help protect you against accidental tap-and-pay transactions while at the register.
The best RFID-blocking wallets and bags
If you need a new bag or wallet, there are plenty of RFID-blocking options available. Check them out ahead, from Herschel, Samsonite and more brands. There are wallets, backpacks and handbags here for a variety of budgets. They're all rated four stars or more.
The Travando slim money clip wallet is a No. 1 Amazon bestseller. The 4.5" x 3.1" x 0.6" wallet features 11 card pockets, an integrated money clip and -- of course -- it's RFID-protected. Available in 14 colors.

709
SMS Spunmelt Nonwoven Production Line Non Woven Fabric Making Machine SMS Machine



We believe that with our improvements, we will be able to provide more quality and reliable PP Non woven fabric machine, non woven fabric production line, spunbond nonwoven production line to all our customers while significantly increasing our production capacity. Our company takes the brand building work as a strategic task to win the market and improve the market share. We have established a good and stable partnership with many well-known brand enterprises. Customers from all walks of life are welcome to come to the factory for communication, visit and guidance. Our company brings together the top talents in the industry and builds a dynamic enterprise full of innovation.Get more news about Hot Sale Smmss Non-woven Non-woven Fabric Production Equipment,you can vist our website!

Application: The product is featured by Medical and Health, Hygiene product, Operation suit, exposure suit, cap, mask, massage cloth, baby diaper, women napkin and so on. Our machines are exported overseas and have exhibition points in many countries.
We have a wealth of experience to ensure that every machine provided to our customers is of high quality. In addition, we also give away one year of free parts and a two-year quality guarantee period, so you can buy with confidence.
Besides, A.L supports our customers service 24 hours A day, 7 days work, any inquiry could be replied within 1 hour pre-sales and after-sales.
We adhere to the interests of all relevant parties, firm confidence, fulfill the mission, and strive to build the company into an international manufacturer of SMS Spunmelt Nonwoven Production Line Non Woven Fabric Making Machine SMS Machine that trusted by the public and preferred by customers. Our team members are aim to provides products with high performance cost ratio to our customers, and the goal for all of us is to satisfy our consumers from all over the world. We have a perfect quality inspection system to ensure the qualification rate of our products, and some of them have successfully entered the international market.

710
UF Veterinary Medicine Central Utility Plant



The old facility’s existing equipment and infrastructure had become outdated and unreliable, presenting the risk of machine failure and restricting steam and chilled water capacity. Without proper functioning, heating and cooling for the entire College could not operate at ideal ranges, or it could even stop entirely. This risk, combined with the need for more space in the undersized facility, made it clear that the College was due for an upgrade.Get more news about uf equipment producer,you can vist our website!

The ability to accommodate the College’s plans of continued growth over time became central to the design. Careful consideration was given to how the location, size, and configuration of equipment would advance these goals.

The building allots space to add equipment, and the configuration gives plenty of leeway for equipment to be modified in place with larger, higher-capacity components as needed. This expand-in-place strategy challenged the notion that design must include extensive unused square footage to prepare for future expansion.The plant faces a prominent entry to the College, unlike typical central plants that are typically tucked away out of view, and therefore needed an attractive exterior design. Large windows put the colorful equipment on display, while clerestory windows create an open and airy interior. The modern, sophisticated entry makes a powerful first impression, essential for a facility that offers regular tours. Steel construction was enveloped in metal panel, cement plaster, and glass, in harmony with the surrounding College of Veterinary Medicine area.

Inside, new machinery includes several magnetic bearing chillers, boilers, chilled water piping, and towers with 4,000-ton capacity.

The new building introduces several energy-efficient solutions. Combined heat and power systems were installed as an energy-efficient method to generate both heat and water. Traditional boilers with feedwater economizers and blowdown heat recovery improve the efficiency of the steam system. The plant contains high-efficiency chillers and chiller plant optimization software designed to reduce the overall electric use of the system over the range of loading.

711
Vertical Shrinkless Expander With Clamping Fixture



Forced tube expander is the key to process high quality air conditioner heat exchanger The equipment adopts multi axis numerical control technology to realize position conversion, workpiece height adjustment and expansion Get more news about Shrinkless Expanding Machine,you can vist our website!

It has the advantages of high degree of automation, convenient operation and good performance

Depending on the characteristics of characteristic:

1.Forced clamping at both ends of the workpiece, and then expanding the tube, the length of the workpiece will not change and there will be no shrinkage deformation, which can save 3 ~ 5% of the raw materials.

2.The rotation table is used to transpose the position, which realizes the simultaneous completion of two-stage expansion and tube expansion on one machine.

3.The tube expansion height, expansion depth and rotary table positioning are all controlled by servo motor.
United States Harry C. Donaldson, Jr., Troy, and Thomas A. Bramtitt, Watervliet, N. Y., assignors Vto Cine, Peabody da Co., Inc., Troy, N. Y., a corporation of New York Application April 27, 1955, Serial No. 504,221
3 Claims. (Cl. i12- 262) This 4invention concerns a method of manufacturing a seam which obviates or at least alleviates the problem of seam shrinkage. When two or 'more fabrics which are perfectly stable, that is which show no tendency to shrink, are sewn together, and then laundered, they heretofore would inevitably shrink and shorten along the seam. Seam shrinkage is the pucker or contraction which occurs upon laundering at seams, especially at those seams in which several plies of fabric are joined. lt is a wellknown and much studied problem in the textile industry. The pucker is unsightly and unattractive and seriously detracts from the appearance of a garment, but more than that and perhaps more important, it represents a dimensional change which causes fitted garments to become too tight or too short.
It is self-evident that in a seam Athe several plies are squeezed tightly together and will, when conditions permit, 'tend to resume their normal plump equilibrium condition. 'Ihe swelling effects of water on cellulosic fabrics permit this readjustment, and the swelling plasticizing and lubricating eifects of water and heat promote similar release for the more hydrophobic fabrics. T he small quantity of fabric yarns encircled by the threads of a single stitch when swelled by water become thicker and the vertical (normal to the seam) diameter of the stitch must become greater, which it can only do at the expense of the horizontal diameter, Vthat is, the length of the stitch. Obviously as each stitch becomes shorter, the seam becomes shorter. The theoretical cure is also obvious, excess thread in each stitch is necessary. if there is excess thread, the stitch and the seam can become thicker without becoming shorter. A loo-se seam would, therefore, be an answer rbut it is impossible to form a loose seam in machine sewing. There are some indirect approaches to the loose seam, such as sewing a piece of cardboard or heavy paper into the seam and then tearing it out. That method adequately prevents seam shrinkage, but is not efficient for high speed mass production efforts. In addition,l a loose seam is less attractive and less reliable than a tight seam. v
A better answer is to sew a tight `seam with a thread which Will become longer when laundered. 011e such thread suggested is a composite of a water soluble yarn and the normal sewing thread twisted together. When the water soluble component is removed as by laundering, there is excess thread in the seam by reason of the now unnecessary spirality. This is a reasonable answer to the problem, but the water soluble component must have af yield point and stress strain behavior approximately that of the permanent component or the spirality and eiectiveness of the composite will change under the tension of sewing. This property of high yield point vand high strength, equivalent to a typical sewing thread, is
dilicult to realize in a water soluble yarn, which yarns are for the most part Very elastic. In addition, the aforementioned equivalency of stress `strain behavior, when realized, `is almost inevitably lost by the plasticizing iniluence of Water vapor at high humidities upon the water ICC soluble component.` The bulky composite thread is difficult to pull through the fabric and causes excessive needle heat. The composite thread therefore, although it offers a theoretical cure for seam shrinkage is not commercially attractive.
We have discovered a means of producing a seam which does not shrink appreciably and which avoids the diculties attendant upon the Iuse of the composite thread mentioned above. Our seam makes use of a temporary or removable yarn which is water soluble, water dispersible or otherwise destructible or removable by water or laundering solutions. For the sake of brevity, we may refer to this yarn as the removable or temporary yarn and it is to be understood that we are not restricting `ourselves to only those yarns which are soluble in pure water. The water may, for instance, contain soaps, alkalies, detergents and other typical laundering assistants which assist in the removal of the temporary yarns. In addition, the sor-called water soluble yarn need not be truly soluble in the laundry solution, for seam shrinkage is adequately minimized if the yarn is merely dispersed or otherwise destroyed or removed by the laundering solution without actually being dissolved therein.. Therefore, water soluble or water destructible yarn is to be understood as meaning and including in its scope as equivalents a yarn which is dissolved, dispersed or otherwise destroyed or removed by a laundering solution.

712
Hydraulic Press Machine Series for Rubber and Silicone Molding



French Oil Mill Machinery Company’s cost-effective hydraulic press machine series, TMP Asian, is a standard hydraulic press product line that offers presses for compression, vacuum and injection molding of rubber and silicone components for a broad range of industries, including but not limited to automotive, consumer, industrial, medical and sporting.Get more news about vacuum hydraulic machine,you can vist our website!

The Econo-Jet RIVH rubber injection molding press series features a specialized two-stage material supply. It eliminates the presence of dead material in the injection system by effectively expelling bubbles out of the raw material. Econo-Jet models are offered with capacities from 200 to 600 tons.

The Econo-Tech RC compression molding press system uses double mold plates for high speed production capabilities. The hydraulic press machine is self-contained, and is designed with a central control system. Econo-Tech presses are available in 200 to 600 ton models with platen sizes ranging from 550mm to 950mm square.

TMP Asian also offers a line of Vacu-Jet vacuum molding presses. Our presses are shipped directly from our Piqua, Ohio facility, and are serviced by our experienced team of technicians to help reduce downtime concerns. The combined technology, cost-effectiveness, and dedicated aftermarket service support make purchasing TMP Asian a prudent choice. Please contact us or download a product brochure to learn more. We look forward to sharing the benefits of TMP Asian with you.

713
Lowepro Toploader Pro 70 AW Camera Case Review



If you find me shooting, you will probably also find at least one Lowepro Toploader Pro hanging from my shoulder or attached to a Lowepro Belt I am wearing. These cases are by far my most-used. Why? Foremost, because the toploading holster-style cases offer fast access to a ready-to-use camera while providing excellent protection in a compact and comfortable-to-carry design.Get more news about toploader holder production,you can vist our website!

If you have read the Lowepro Toploader Pro 75 AW Review or the Lowepro Toploader Pro 65 AW Review, the Lowepro Toploader Pro 70 AW review will sounds very familiar. These cases are nearly the same except for their dimensions.

Lowepro's cases are extremely popular due to their great quality, great designs and reasonable pricing. Lowepro's Toploader Pro Cases are no exception to this rule.

As of Lowepro Toploader Pro 70 AW review time, there are three Lowepro Toploader Pro models to choose from. The 70 AW is the middle child in this family. Use the mouseover links below to tour these models.Each case has a zippered pocket in the front. The size of this of pocket varies significantly between models with the 70 AW's pocket able to comfortably hold a Canon 320EX Speedlite Flash. I don't have a Canon 430EX II Speedlite Flash available right now, but I think it will also fit. This is also a great area to store filters in their plastic boxes.

An elastic mesh inner pocket will keep smaller items in place. I sometimes carry a small gray card here. the pocket is moderately padded on the outside and heavily padded against the inside of the case. A small elastic pen holder pocket is available on the outside.

The above picture shows the Lowepro Toploader Pro 70 AW front pocket forced open wide. The main compartment zipper pulls are visible in this shot. Note the easy-to-grip U-shaped zipper pulls - I really appreciate this design in the heat of the action.

Moving to the Side 1 image above, you can see a key feature of this case: the large, strong nylon web with dual sets of heavy stitching running vertically through it. This is the Lowepro Slip Lock attachment point. As part of the Lowepro Street and Field modular carrying system, the Lowepro Toploader Pro 70 AW accepts a huge range of accessories that attach via Slip Lock - including lens cases, water bottle holders and other general accessories.

The older Lowepro Toploaders (non-"Pro" models) had two of these attachments - and I was not happy to have only one on the new Pro models. Reality is that I have not missed the second Slip Lock attachment very much - but I frequently make use of the available one.

714
What is artificial stone?
Artificial stone, which is also called casted stone, is constructed from cement, sand , and natural aggregate such as crushed stone. it is possible to provide certain surface textures to artificial stones. Sometimes, specific pigments used to achieve certain color. The addition of pigments shall not exceed 15% by volume. Artificial stone can be cast into complicated and considerably detailed forms and various sizes can be manufactured. Added to that, it can be reinforced to increase strength. Finally, it is worth mentioning that artificial stones are casted easily and economically.Get more news about artificial stone ingredients,you can vist our website!
When artificial stones are selected for building constructions?
Artificial stone or cast stone will be used for construction when cost effective and durable natural stone cannot be achieved.
What are the types of artificial stones?
Different types of artificial stones along with their constituent materials and applications will be discussed briefly.
Ransom stone
It is also called chemical stone which its compression strength is at least 32 MPa. Ransom stone is manufactured by blending silica soda with cement to provide fancy and ornamental flooring.
It is constructed from Portland gypsum cement and sand using either precast or cast in situ technique. For precast production technique, the casted artificial marble will be stripped from the mould after three days and then treated with liquid fluorite of magnesia solution at the age of five days. After that, the stone is washed and wrapped with paper for 24 hours and treated again with the same solution, and it will be polished at the final stage at the age of 30days. For in situ construction method, layer of prepared mixture is placed on a canvas, and the thickness of the layer shall be 1.5 mm greater than the required thickness of the stone to be constructed. The surface of the laid layer is rubbed and then polished properly.
Victoria stone
It is a granite piece which its surface is hardened by submerged the stone in silica soda for two months.  Garlic stone Garlic stone, which is employed as a surface drains and flag stones, is produced by mixing and casting Portland cement and iron slag.
Imperial stone
The procedure used to produce imperial artificial stone includes careful washing of finely crushed granite, mixing granite with Portland cement, cast the mixture into a favored form, and finally steam cure the casted imperial stone for twenty-four hours.

715
Best smart lighting for your connected home



Smart LED bulbs that can be controlled by a hub or smartphone app are no longer a new idea. What is new is how far this technology has come since its advent just a few years ago. Also new: Products like the Nanoleaf Light Panels—a system of interlocking LED panels that let you decorate with light—fundamentally change the light-bulb concept.Get more news about Best Cold Light Line,you can vist our website!

Smart LED bulbs aren’t quite a commodity, but they are getting close to maturity as far as the market goes. Today’s bulbs are more compact, much brighter, have better color representation, and, for the most part, feature control apps that do more than ever and are easier to set up. Prices have also come down, with some no-name color-tunable bulbs now available for less than $10 each. (Buyer beware: You get what you pay for.)

Philips (now known as Signify) was one of the first players in this market, and the company’s experience shows. The recent addition Bluetooth support obviates the need for the $60 Philips Hue Bridge (although most smart home denizens will want the Bridge anyway). Signify’s Philips Hue lighting ecosystem is the industry’s deepest and broadest, with bulbs of every shape and size imaginable, not to mention lighting fixtures landscape lighting.

Wyze Labs can’t match Philips Hue in terms of the breadth of its smart lighting ecosystem, but it beats Signify’s brand by a country mile in terms of pricing, and Wyze has a much broader array of product offerings when it comes to other areas of the smart home–most importantly in terms of home security. Wyze also now offers an excellent BR30 color smart bulb.

Our choice won’t surprise anyone who’s been following this market. Philips dominates this space and is also our top pick for best color LED smart bulb. The latest Hue bulbs can be controlled via Bluetooth or Zigbee (the latter requires the Philips Hue Bridge), they deliver high-quality light, and are backed by a strong warranty. We only received the BR30 form factor for our review, but apart from form factor, that bulb is the same as the A19.

716
Use of Elastomeric Separators in Maxillofacial Fracture Reduction



Background: Management of maxilla and mandibular fractures are based on the principles of reduction, fixation and immobilization of the fracture segments.Get more news about Elastomer Separators,you can vist our website!

Purpose: One of the processes of reduction is to apply continuous and gradual elastic traction by placing elastics from the upper and lower arch bars in a definite manner and direction as per the fracture line. Orthodontic elastic separators are versatile, and the major advantage is the higher traction forces as compared to conventional elastics.

Methods: Prestretched separator elastics were guided over the arch bar or fixed orthodontic appliances to provide desired traction.

Results: Orthodontic elastic separators are therefore versatile, and the major advantage is the higher traction forces as compared to conventional elastics. They provide an edge over the use of wires as they tend to break off by work hardening.

Conclusion: Therefore, we have adapted orthodontic separators and have used them in place of conventional elastics for the last 10 years with appreciable results after taking informed consent from the patients.

717
POLISHED VS. UNPOLISHED PORCELAIN TILES: WHICH IS PREFERRED?



Porcelain tiles look amazing and match almost any decor and furniture. Also, they are preferred by homeowners and designers too. However, people always get confused about polished porcelain vs. unpolished porcelain tiles.Get more news about Glazed Polished Porcelain Tile,you can vist our website!

Therefore, whether to utilize polished porcelain tiles or unpolished porcelain tiles is a point of contention.

Seems like a difficult task? Worry not! In this article, we have shown the difference between polished porcelain tiles and unpolished porcelain and cleared out which one to use for decoration purposes and where.

Polished vs. Unpolished Porcelain Tiles: 8 Major Differences
Porcelain tiles are polished by machine to achieve a mirror-like sheen and rectified by squaring the tile's edges. The tile's gleaming lustre provides a rich, high-end appearance that makes your floor look fantastic!

In this write-up, we will examine the differences between these two types and attempt to understand them better. So, without further ado, let's get started.

Production Method
Polished porcelain floor tiles are made by polishing the surface of the tile with a diamond disc to give a gleaming texture. But no such polishing occurs to the unpolished one.

Furthermore, when polished porcelain tiles are made, it forms microscopic pours that are concealed by a shiny finish. Excluding the final phase, the manufacturing process for both tiles is almost similar.

Outer Finishing
Polished porcelain tiles have a sparkling and smooth feel, as one might anticipate. They are mostly available in two types: glazed and unglazed.

On the contrary, unpolished porcelain tiles often have plain surfaces and, unlike polished porcelain tiles, do not come in glazed and unglazed varieties.

Moreover, polished porcelain tiles typically have a 3D surface, but unpolished ones usually have a matte or honed surface.

Implementation
Polished porcelain tiles have a glossy and slippery surface, so they are most suitable for interior settings. However, shiny and sleepy surfaces are not a good fit for high-traffic spots, so it's better to use them indoors.

In contrast, unpolished porcelain tiles have plain surfaces, making them the perfect fit for the outdoors. It is also a great fit for the bathrooms and any wet place, as it's less slippery.

718
Benefits of combining transfer cars with the Pallet Shuttle in a warehouse



Combining transfer cars with the Pallet Shuttle in a logistics center boosts throughput in storing and retrieving products from their locations. This automated storage system speeds up pallet movements and goods handling.Get more news about Automatic Shuttle Transfer System,you can vist our website!

The automated Pallet Shuttle is a prime example of the efficiency of high-density storage systems. It works like this: automatic handling equipment, i.e., transfer cars or stacker cranes, transports materials to their storage channels; once there, an autonomous electric shuttle inserts and removes pallets from their locations. This automated system notably reduces goods loading and unloading times.

Transfer cars with the Pallet Shuttle: how do they work?
The storage solution that combines transfer cars with the Pallet Shuttle is the automated Pallet Shuttle. This system, which replaces forklifts, consists of multiple motorized shuttles — served by transfer cars — that move automatically inside the storage channels.

In this completely automated storage solution, transfer cars transport a motor-driven shuttle in their cradles. The shuttle then enters the storage channel to deposit the pallet in the first free location. Then, the shuttle returns to the transfer car to go back to the entry point, repeating the operation as indicated by the system.

The configuration of the Pallet Shuttle operated with transfer cars maximizes the productivity of the automated storage and retrieval system (AS/RS). At a minimum, each level of the automated Pallet Shuttle system is operated by a motorized shuttle and a transfer car. Lifts are used to connect the different levels of the AS/RS, performing movements from the floor level to the required height. All automatic movements — of both the shuttles and the transfer cars — are coordinated by the warehouse management system (WMS).

The automated Pallet Shuttle is a high-density storage system: it decreases the number of aisles in which the handling equipment operates and compacts the locations that house the goods. Employing transfer cars to move the motor-driven shuttles means that the aisles can be narrower, thus optimizing floor space.
Ultimately, the combination of transfer cars with the Pallet Shuttle fosters a more productive warehouse with safe, continuous, error-free processes. This AS/RS is versatile and can be adapted to the characteristics of your facility: the layout, number of SKUs per channel, and even operations involving pallets of different dimensions.

719
Amish Jewelry Box Buying Guide


Whether you’re searching for a gift or the right storage for your own collection, the Amish Jewelry Box Buying Guide can offer helpful tips. Read on for guidance on what to look for to find the best jewelry box to meet your needs.Get more news about Personalised Wooden Jewelry Box,you can vist our website!

Types of Jewelry Storage
There are many different types of jewelry storage, ranging from small to large in size. There are different materials to choose from, and you can find jewelry storage to fit any budget from inexpensive to high-end. Some options available include:

Hanging Jewelry Organizers—These are inexpensive and can hang on a hook. They have plastic compartments so you can easily view and access jewelry. They are not as sophisticated as other jewelry storage and won’t last as long, but they are affordable and practical.

Over-the-Door Jewelry Organizers—These are similar to hanging jewelry organizers, except they have hooks that hang over the door. They are a good space saver option.

Travel Jewelry Organizers—These are available in a variety of sizes from small box or pouch to a roll-up fabric case you can tuck in your luggage. They are lightweight and some have soft linings.

Jewelry Organizer Trays—These are stackable trays with compartments for storage. They are often made of plastic and are an inexpensive option.

Standing Jewelry Armoires—These come in a variety of sizes and can hold larger collections. They can be heavy and take up a good amount of space. They can contribute to the style of the room as another piece of furniture.

Jewelry Box—These are the oldest and most popular versions for jewelry storage. They come in a variety of sizes and styles. They sit easily on a flat surface.

Men’s Jewelry Box—These are also called valets and offer simpler styles than women’s jewelry boxes. They often have a single tray, and are used to hold watches, cufflinks, coins, wallet, rings, money clips and more.

720
What is Swiss Machining?



Swiss machining is similar to conventional turning on a lathe, but the difference lies in how the stock material is moved and supported. A standard lathe with a fixed headstock is designed only to spin the stock material; aside from its rotation, the material is held perfectly still in its collet. The cutting tool is the part that moves along the material to make the proper cuts. In Swiss machining, the material passes through a sliding headstock and a guide bushing, sliding down the longitudinal axis of the machine. So why is this difference important?Get more news about Swiss-type Lathe Machining,you can vist our website!

History of Swiss Style Lathes
Although Swiss machining has only become a buzz term in the past decade or so, it was actually developed in Switzerland in the 1870s as a solution for the watch-making industry. Inventor Jakob Schweizer created a lathe with a sliding headstock in an effort to find a more efficient way to produce the thin parts he needed for his watches. His contraption is one of the reasons that the world’s most famous watchmaker, Rolex, is from Switzerland. Within a decade of Schweizer’s creation of the Swiss machine, his idea was being mass-produced and spreading over the globe. Today’s Swiss machines look very different than the first machines that were made almost 150 years ago, but their niche remains the same: machining small, thin parts that no other machine can.

Where are Swiss Machines Used?
Imagine holding a long, thin stick between your hands. If you were to rub your hands together quickly to make the stick spin, the part of the stick closest to your hands would be most stable, but the end of the stick wouldn’t be so much spinning on its axis – as whipping around in a circle. This concept is what makes Swiss machines so useful. Long, narrow parts are predisposed to wobbling more and more towards the end that is not held by the machine because of their centripetal force. In a Swiss machine, the guide bushing eliminates the problems this can cause by supporting the material as close to the cutting tool as safely possible (as close as 0.020”–0.080”). Even at aggressive speeds, parts are unlikely to deflect or be gouged. While it is recommended to use a Swiss machine for any part that has a 3:1 length to width ratio or greater, most Swiss machines can cut parts with up to a 20:1 length to width ratio without issue.

Historically, the medical industry has been the dominant user of Swiss machining. Bone screws especially were difficult – if not impossible – to machine to specifications with standard lathes. The screws present a number of machining complications: their length to width ratios are often very high; they are mostly machined from titanium, which is known for its poor heat conductivity and likelihood to create problems with chip load; and their tolerances are extremely tight so that the patient is both safe and comfortable. Modern bone screws even have multi-start threads, where two or more threads go around the screw at least one full turn, increasing the complexity of the overall part. Taken altogether, it becomes clear that Swiss machining is the best option for machining situations like this.

These days, almost every manufacturing industry uses Swiss machining. As the tolerances on customer parts become tighter and tighter and the margin for profitability becomes slimmer and slimmer, Swiss machining becomes increasingly valuable. Not only does it make a greater range of part production possible, it also heightens the quality of existing parts while reducing their cycle times. Any reputable, high-production, modern aerospace, oil and gas, automotive, defense, or electronics shop will have a Swiss machine.

What Materials Are Used in Swiss Machining?
Swiss machines offer a distinct advantage over conventional lathes in the range of materials that they can cut safely. Most often, Swiss parts are machined from common materials like aluminum, titanium, and stainless steel. However, many manufacturers use nickel alloys, carbon steel, bronze, brass, and copper. Swiss machines can even cut plastics, often as a cost-effective and more precise alternative to injection molding for creating prototypes. Virtually any rigid plastic can be used, but the most common are Polycarbonate and Teflon.

Sivuja: 1 ... 46 47 [48] 49 50 ... 177